Understanding Plumbing Basics is Essential for Bathtub Installation
Understanding Plumbing Basics is Essential for Bathtub Installation
Blog Article
This post which follows about How to Install a Bathtub is exceptionally motivating. You should read it.
Mounting a bathtub isn't specifically brain surgery, however it does need strong plumbing, woodworking, and also in some cases, tiling skills. Changing an old bath tub with a brand-new one is additionally a moderately difficult task. If the old bathtub is readily accessible, the task can move quickly; if you have to open up a wall to eliminate the old tub and also place the brand-new bathtub, the task is much harder. In either case, the job is within a residence handyman's abilities, although you will need an assistant to move out the old bathtub as well as embeded in the brand-new one. See to it you have certified yourself for the task as well as fit attempting it. Rather than employing a contractor to take over a halfway-completed job, it is better to consider employing one before you start. Possibilities are you might require an expert plumber to make tube links.
This write-up will certainly help you set up a new bath tub in your restroom if you have currently purchased a new bathtub and do not require to alter the setup of your previous water supply pipes.
Your tools and material list should comprise the following:
Removing Old Touches
If you need to replace old taps with new ones as a part of your installation, after that the first thing you ought to do is detach the water supply. After doing so, turn on the faucets to drain any type of water staying in the system. The procedure of getting rid of the existing taps can be rather bothersome due to the restricted accessibility that is typically the instance.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipelines to the faucets. Have a cloth prepared for the continuing to be water that will certainly originate from the pipes. As soon as the supply pipes have been removed, make use of the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from turning during this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any kind of old sealing compound.
Prior to going on to fit the new taps, compare the pipeline connections on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic port to stop damages to the string. One end of the adapter fits on the plastic tail of the tap and the other end gives a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly require reducing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the faucet in the installing opening in the bath/basin making sure that the washers remain in place in between the faucet and the sink. Protect the faucet in position with the manufacturer supplied backnut. As soon as the tap is firmly in position, the supply pipes can be attached to the tails of the taps. The taps can either be connected by using corrugated copper piping or with typical faucet adapters. The previous type must be attached to the faucet ends first, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Installing the Bathtub
Making use of the two wood boards under its feet, position the bathtub in the required placement. The wooden boards are helpful in uniformly spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 small points.
The next goal is to guarantee that the tub is leveled all round. This can be achieved by checking the level and also adjusting the feet on the bath tub until the level reviews degree.
To set up faucets, fit all-time low of the outermost adaptable tap connector to the suitable supply pipeline by making a compression sign up with; after that do the same for the other faucet.
Turn on the water supply and inspect all joints and new pipework for leaks and also tighten them if essential. Fill the tub and also inspect the overflow electrical outlet and also the normal electrical outlet for leaks.
Ultimately, fix the bath paneling as described in the supplier's instruction manual. Tiling and securing around the tub should wait till the bathtub has been utilized at the very least once as this will certainly settle it right into its final placement.
Getting ready for the Installation
To start with, the sustaining frame supplied with the bathroom needs to be fitted (if required) according to the maker's guidelines. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to see to it that if the tap comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bath, it is likewise sensible to fit a sustaining plate under the taps device to prevent pressure on the tub.
Fit the adaptable tap ports to the bottom of the two taps utilizing 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet via the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you make use of all of the supplied washing machines.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be fitted in its final placement.
Tiling Around the Bathtub
In the area where the bathroom fulfills the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the installation can move enough to break a stiff seal, causing the water to penetrate the wall in between the bathroom and the tiling, causing complications with moisture as well as feasible leakages to the ceiling below.
You can pick from a variety of coloured sealants to blend in your fixtures and also installations. They are offered in tubes and also cartridges, as well as are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with spins of drenched paper or soft rope. Keep in mind to constantly fill the tub with water prior to securing, to allow for the movement experienced when the tub remains in use. The sealant can break rather early if you do not consider this motion prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also conveniently offered on the market. It is suggested to fit the floor tiles making use of waterproof or waterproof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been introduced to that article about A Step-by-Step Guide to Installing a Bathtub through an associate on another website. In case you appreciated our blog entry plz remember to share it. Thank-you for your time invested reading it.
Trust us, dial! Report this page